Heat and Cooling losses ... Foiled

Our Customers SPEAK UP... "Late Breaking News" ... Go there NOW!

Foil 101, Its your Money! (reading time 6 minutes)

HEAT GAIN / LOSS IN BUILDINGS...

There are three modes of heat transfer: CONDUCTION, CONVECTION, and RADIATION (INFRARED). Of the three, radiation is the primary mode; conduction and convection are secondary and come into play only as matter interrupts or interferes with radiant heat transfer. As matter absorbs radiant energy, it is heated and a gradient temperature develops, which results in molecular motion (conduction in solids) or mass motion (convection in liquids and gas). This is to much knowledge.. I want the Answer!

All substances, including air spaces and building materials (such as wood, glass, plaster and insulation), obey the same laws of nature and TRANSFER heat. Solid materials differ only in the rate of heat transfer, which is mainly affected by differences in density, weight, shape, permeability and molecular structure. Materials which transfer heat slowly can be said to RESIST heat flow.

Direction of heat transfer is an important consideration. Heat is radiated and conducted in all directions, but convected primarily upward. The figures below show modes of heat loss by houses. In all cases, radiation is the dominant mode.

CONDUCTION is direct heat flow through matter (molecular motion). It results from actual PHYSICAL CONTACT of one part of the same body with another part, or of one body with another. For instance, if one end of an iron rod is heated, the heat travels by conduction through the metal to the other end; it also travels to the surface and is conducted to the surrounding air, which is another, but less dense, body. An example of conduction through contact between two solids is a cooking pot on the solid surface of a hot stove. The greatest flow of heat possible between materials is where there is a direct conduction between solids. Heat is always conducted from warm to cold, never from cold to warm, and always moves via the shortest and easiest route.

In general, the more dense a substance, the better conductor it is. Solid rock, glass and aluminum-being very dense-are good conductors of heat. Reduce their density by mixing air into the mass, and their conductivity is reduced. Because air has low density, the percentage of heat transferred by conduction through air is comparatively small. Two thin sheets of aluminum foil with about one inch of air space in between weigh less than one ounce per square foot. The ratio is approximately 1 of mass to 100 of air, most important in reducing heat flow by conduction. The less dense the mass, the less will be the flow of heat by conduction.

CONVECTION is the transport of heat within a gas or liquid, caused by the actual flow of the material itself (mass motion). In building spaces, natural convection heat flow is largely upward, somewhat sideways, not downward. This is called "free convection."

For instance, a warm stove, person, floor, wall, etc., loses heat by conduction to the colder air in contact with it. This added heat activates (warms) the molecules of the air which expand, becoming less dense, and rise. Cooler, heavier air rushes in from the side and below to replace it. The popular expression "hot air rises" is exemplified by smoke rising from a chimney or a Fire. The motion is turbulently upward, with a component of sideways motion. Convection may also be mechanically induced, as by a fan. This is called "forced convection."

RADIATION is the transmission of electromagnetic rays through space. Radiation, like radio waves, is invisible. Infrared rays occur between light and radar waves (between the 3 -15 micron portion of the spectrum). Henceforth, when we speak of radiation, we refer only to infrared rays. Each material that has a temperature above absolute zero (-459-7 F.) emits infrared radiation, including the sun, icebergs, stoves or radiators, humans, animals, furniture, ceilings, walls, floors, etc.

All objects radiate infrared rays from their surfaces in all directions, in a straight line, until they are reflected or absorbed by another object. Traveling at the speed of light, these rays are invisible, and they have NO TEMPERATURE, only ENERGY. Heating an object excites the surface molecules, causing them to give off infrared radiation. When these infrared rays strike the surface of another object, the rays are absorbed and only then is heat produced in the object. This heat spreads throughout the mass by conduction. The heated object then transmits infrared rays from exposed surfaces by radiation if these surfaces are exposed directly to an air space.

The amount of radiation emitted is a function of the EMISSIVITY factor of the source's surface. EMISSIVITY is the rate at which radiation (EMISSION) is given off. Absorption of radiation by an object is proportional to the absorptivity factor of its surface which is reciprocal of its emissivity.

Although two objects may be identical, if the surface of one were covered with a material of 90% emissivity, and the surface of the other with a material of 5% emissivity, the result would be a drastic difference in the rate of radiation flow from these two objects. This is demonstrated by comparison of four identical, equally heated iron radiators covered with different materials. Paint one with aluminum paint and another with ordinary enamel. Cover the third with asbestos and the fourth with aluminum foil. Although all have the same temperature, the one covered with aluminum foil would radiate the least (lowest [3%] emissivity). The radiators covered with ordinary paint or asbestos would radiate most because they have the highest emissivity (even higher than the original iron). Painting over the aluminum paint or foil with ordinary paint changes the surface to 90% emissivity.

Materials whose surfaces do not appreciably reflect infrared rays, i.e.: paper, asphalt, wood, glass and rock, have absorption and emissivity rates ranging from 80% to 93%. Most materials used in building construction -- brick, stone, wood, paper, and so on -- regardless of their color, absorb infrared radiation at about 90%. It is interesting to note that a mirror of glass is an excellent reflector of light but a very poor reflector of infrared radiation. Mirrors have about the same reflectivity for infrared as a heavy coating of black paint.

The surface of aluminum has the ability NOT TO ABSORB, but TO REFLECT 97% of the infrared rays which strike it. Since aluminum foil has such a low mass to air ratio, very little conduction can take place, particularly when only 3% of the rays are absorbed.

TRY THIS EXPERIMENT: Hold a sample of FOIL INSULATION close to your face, without touching. Soon you will feel the warmth of your own infrared rays bounding back from the SURFACE. The explanation: The emissivity of heat radiation of the surface of your face is 99%- The absorption of aluminum is only 3%. It sends back 97% of the rays. The absorption rate of your face is 99%. The net result is that you feel the warmth of your face reflected.

REFLECTIVITY AND AIR SPACES

In order to retard heat flow by conduction, walls and roofs are build with internal air spaces. Conduction and convection through these air spaces combined represent only 20% to 35% of the heat which pass through them. In both winter and summer, 65% to 80% of the heat that passes from a warm wall to a colder wall or through a ventilated attic does so by radiation.

The value of air spaces as thermal insulation must include the character of the enclosing surfaces. The surfaces greatly affect the amount of energy transferred by radiation, depending on the material's absorptivity and emissivity, and are the only way of modifying the total heat transferred across a given space. The importance of radiation cannot be overlooked in problems involving ordinary room temperatures.

The following test results illustrate how heat transfer across a given air space may be modified. The distance between the hot and cold walls is 1-1/2" and the temperatures of the hot and cold surfaces are 212 degrees and 32 degrees, respectively. In CASE 1, the enclosing walls are paper, wood, asbestos or other similar material. In CASE 2, the walls are lined with aluminum foil. In CASE 3, two sheets of aluminum foil are used to divide the enclosure into three 1/2" spaces.

Conduction 21 BTU's

Convection 92 BTU's

Radiation 206 BTU's

TOTAL 319 BTU'S

CASE 1, UNINSULATED WALL SPACE.

The surfaces of ordinary building materials, including ordinary bulk insulation have a radiation or emissivity rate of about 90%, a heat ray absorption rate of over 90%. Air has low density, so conduction is slight (only 21 BTU'sJ Convection currents transfer 90 BTU's.

Conduction 21 BTU's

Convection 92 BTU's

Radiation 10 BTU's

TOTAL »123 BTU'S

CASE 2, THE SAME WALL SPACE EXCEPT

that the inner surfaces were lined with sheets of aluminum foil of 5% emissivity and absorptivity.* Note the drastic drop in heat flow by radiation, from 206 BTU's to 10 BTU's. Conduction and convection are unchanged. The original total heat loss of 319 BTU's drops to 123 BTU's.

Conduction 23 BTU's

Convection 23 BTU's

Radiation 2 BTU's

TOTAL 48 BTU'S

CASE 3, TWO SHEETS OF (5% EMISSIVE)

ALUMINUM FOIL divide the wall space into 3 reflective compartments. Heat loss by radiation drops 94% from Case 1. The 2 interior sheets retard convection so that its flow falls 75%. Conduction rises only 2 BTU's; from 21 BTU's to 23 BTU's. The total heat loss drops 85% from Case 1.

Reflection and emissivity by surfaces can ONLY occur in SPACE. The ideal space is any dimension 3/4" or more. Smaller spaces are also effective, but decreasingly so. Where there is no air space, we have conduction through solids. When a reflective surface of a material is attached to a ceiling, floor or wall, that particular surface ceases to have radiant insulation value at the points in contact.

Heat control with aluminum foil is made possible by taking advantage of its low thermal emissivity and the low thermal conductivity of air. It is possible with layered foil and air to practically eliminate heat transfer by radiation and convection: a fact employed regularly by the NASA space program. In the space vehicle Columbia, ceramic tiles are imbedded with aluminum bits which reflect heat before it can be absorbed. "Moon suits" are made of reflective foil surfaces surrounding trapped air for major temperature modification.

HEAT LOSS THROUGH AIR

There is no such thing as a "dead" air space as far as heat transfer is concerned, even in the case of a perfectly airtight compartment such as a thermos bottle. Convection currents are inevitable with differences in temperature between surfaces, if air or some other gas is present inside. Since air has some density, there will be some heat transfer by conduction if any surface of a so-called "dead" air space is heated. Finally, radiation, which accounts for 50% to 80% of all heat transfer, will pass through air (or a vacuum) with ease, just as radiation travels the many million miles that separate the earth from the sun.

Aluminum foil, with its reflective surface, can block the flow of radiation. Some foils have higher absorption and emissivity qualities than others. The variations run from 2% to 72%, a differential of over 2000%. Most aluminum insulation has only a 5% absorption and emissivity ratio. It is impervious to water vapor and convection currents, and reflects 95% of all radiant energy which strikes its air-bound surfaces.

HEAT LOSS THROUGH FLOORS

Heat is lost through floors primarily by radiation (up to 93%). When ALUMINUM insulation is installed in the ground floors and crawl spaces of cold buildings, it prevents the heat rays from penetrating down, reflecting the heat back into the building and warming the floor surfaces. Since aluminum is non-permeable, it is unaffected by ground vapors.

CONDENSATION

Water vapor is the gas phase of water. As a gas, it will expand or contract to fill any space it may be in. In a given space, with the air at a given temperature, there is a limited amount of vapor that can be suspended. Any excess will turn into water. The point just before condensation commences is called 100% saturation. The condensation point is called dew point.

VAPOR LAWS

1. The higher the temperature, the more vapor the air can hold; the lower the temperature, the less vapor.
2. The larger the space, the more vapor it can hold; the smaller the space, the less vapor it can hold.
3. The more vapor in a given space, the greater will be its density.
4. Vapor will flow from areas of greater vapor density to those of lower vapor density.
5. Permeability of insulation is a prerequisite for vapor transmission; the less permeable, the less vapor transfer.

The average water vapor saturation is about 65%. If a room were vapor-proofed, and the temperature were gradually lowered, the percentage of saturation would rise until it reached 100%, although the amount of vapor would remain the same. If the temperature were further lowered, the excess amount of the vapor for that temperature in that amount of space would fall out in the form of condensation. This principle is visibly demonstrated when we breathe in cold places. The warm air in our lungs and mouth can support the vapor, but the quantity is too much for the colder air, and so the excess vapor for that temperature condenses and the small particles of water become visible.

In conduction, heat flows to cold. The under surface of a roof, when cold in the winter, extracts heat out of the air with which it is in immediate contact. As a result, that air drops in temperature sufficiently to fall below the dew point (the temperature at which vapor condenses on a surface). The excess amount of vapor for that temperature that falls out as condensation or frost attaches itself to the underside of the roof.

Water vapor is able to penetrate plaster and wood readily. When the vapor comes in contact with materials within walls having a temperature below the dew point of the vapor, moisture or frost is formed within the walls. This moisture tends to accumulate over long periods of time without being noticed, which in time can cause building damage.

To prevent condensation, a large space is needed between outer walls and any insulation which permits vapor to flow through. Reducing the space or the temperature converts vapor to moisture which is then retained. The use of separate vapor barriers or insulation that is also a vapor barrier are alternate methods to deal with this problem. Aluminum is impervious to water vapor and with the trapped air space is immune to vapor condensation.

TESTING THERMAL VALUES

U FACTOR is the rate of heat flow in BTU's in one hour through one sq. ft. area of ceilings, roofs, walls or floors, including insulation (if any) resulting from a 1 degree F. temperature difference between the air inside and the air outside.

MEMORY JOGGER: U = BTU'S flowing ONE hour, through ONE sq. ft. for ONE degree change.

R FACTOR or RESISTANCE to heat flow is the reciprocal of U; in other words, 1/U. The smaller the U factor fraction, the larger the R factor, the better the insulation's ability to stop conductive heat flow. Note: Neither of these factors include radiation or convection flow.

There are at present two kinds of techniques generally used by accepted laboratories to measure thermal values: the guarded hot plate and the hot box methods. The results obtained seem to vary between the two methods. Neither technique simulates heat flow through insulation in actual everyday usage. Thermal conductivity measurements, as made in the completely dry state in the laboratory, will not match the performance of those same insulators under actual field conditions. Most mass type insulating materials become better conductors of heat when the relative humidity increases because of the absorption of moisture by the insulator. (Try keeping your feet in a pair of wet socks.) Therefore, mass insulators, which normally contain at least the average amount of moisture which is in the air, are first completely dried out before testing. In aluminum insulation, there is no moisture problem. Aluminum foil is one of the few insulating materials that is not affected by humidity, and consequently, its insulating value remains unchanged from the "bone dry" state to very high humidity conditions. In addition, when considering adding more R's ... Remember, Fourier's Law of Thermodynamics, "Upgrading from R-13 to R-32, reduces conductive heat flow by only an additional 4%". That doesn't seem cost effective! And, the R Value of a mass type insulation is reduced by over 35% with only a 1-1/2% moisture content, (i.e.: from R13 to R8.3). The moisture content of insulation materials in homes typically exceeds 1 -1/2%! In spite of the advances made by space technology in insulation systems based on understanding and modifying the effects of radiation, no universally accepted laboratory method has yet been devised to measure and report the resistance to heat flow of multi-layer foil. Until such a method that will satisfy rigorous laboratory demands is devised, we must be content to make our judgments on the basis of common sense and experience. There are many different types, grades, and qualities of aluminum foil insulation designed for a variety of applications. Matching the correct foil product to the specific job is extremely important to maximize final performance.

Just in case this is not enough, the reflective technological junkies are encouraged to jump to RIMA... The "mother" of reflective associations. Just a click away .... Here's RIMA